Final distribution boards (FDB)
The last level of distribution, fed from an SMDB, with MCBs and RCBOs for lighting and small-power circuits.

HomeSolutions
Seven product lines from one workshop. Every panel is engineered to your single-line diagram and the consultant’s specification, then tested before it leaves Sharjah.

Power distribution
The first board after the transformer. Our MDBs, power control centres and motor control centres take the incoming supply from the transformer or an upstream panel, meter it, protect it with breakers and earth-leakage units, and distribute it to the building or plant.
Designs up to 3200 A are type-tested by DEKRA and ASTA (Intertek) to IEC 61439-2, and SEWA registers us as a Grade 1 assembler up to 3200 A.

Power distribution
Sub-main distribution boards are installed where a large distribution cable ends and several smaller circuits begin. They are fed from the MDB and feed the final distribution boards on each floor, zone or plant room.
Final distribution boards are the last step: each one divides its feed into lighting and power circuits, with a breaker protecting every circuit. We lay them out so any circuit can be traced quickly, years after handover.

Power quality
Automatic power factor correction (APFC) panels switch capacitor steps in and out as the load changes. Power factor is the ratio of active to apparent power; raising it releases system capacity, supports the voltage, cuts losses and avoids the utility’s poor power factor penalties.
Where drives and other non-linear loads create harmonics, we use detuned reactors to protect the capacitors.

Continuity of supply
An automatic transfer switch panel works with a diesel generator. When the mains supply fails, it starts the generator and transfers the load; when the mains returns, it transfers the load back and stops the generator, with no one on site.
For larger sites we also build generator synchronising panels that run two or more sets in parallel, or in parallel with the mains, and share the load automatically.

Automation
Control panels for single machines and complete production lines. We build the panel and write the logic, so when a machine stops, the operator screen shows why.
We design the HMI screens in-house as well: pump overviews with speed and run hours, calorifier and heater monitors, boiler and solar hot water screens, batching recipes for cement plants and BTU meter data tables.
Recent panels include air handling units, booster pumps, heat pumps, boilers, solar hot water and PV systems, cooling rooms, conveyors, cement crushers, bagging machines and process lines for edible oil refining.

Building control
Direct digital control panels for chillers, heat pumps, AHUs and pumps, wired and labelled for fast BMS integration. Our Vida Dubai Mall master panel is one example.

Services
Most commissioning problems are simple: a missing permissive, a wrong scaling factor, a swapped wire. We find them quickly, because we usually built the panel ourselves.
Our engineers draw every panel in EPLAN and size the busbars and enclosures with Legrand XL PRO³ calculation software, so the drawings submitted to the consultant match the panel delivered to site.
Beyond the lines above, we build these to order, to the same standards and with the same factory tests.
The last level of distribution, fed from an SMDB, with MCBs and RCBOs for lighting and small-power circuits.
One assembly holding the starter for every motor (VFD, soft starter, direct-on-line or star-delta) with protection and status signals to the PLC or BMS.
Duty/standby and duty-assist control for water transfer, drainage and irrigation pumps, with level control, alarms and run-hour counters.
Synchronise two or more generators, or generators with the mains, and share the load between them automatically.
Automatic power factor correction in steps. Detuned reactors protect the capacitors where drives create harmonics.
Enclosures for utility and tenant meters, laid out to the requirements of DEWA, SEWA and the other authorities.
A changeover switch to move a load between mains and generator by hand, where automatic transfer isn’t required.
Local isolation next to plant and equipment, and enclosures to join and split cables on site.
Outdoor pillars with protection, contactors and photocell or timer control for road and community lighting.
Operator desks that bring switches, indicators, meters and HMI screens together at one control-room position.

Start, stop and VFD speed control for fresh-air and air-handling units, with interlocks and BMS points for status and alarms, for healthier, efficient ventilation.

Steady water pressure for towers and villas: pressure sensing, VFDs, duty rotation and an HMI overview showing each pump’s speed and run hours.

Precise temperature control and protection for electric heaters, calorifiers and hot water storage tanks, with an HMI monitor for up to eight heaters.

Run circulation pumps, coolers and backup heaters so the system uses the sun first, with a touchscreen showing collectors, tanks and pumps.

Motor control and master control for heat pump plants, staging units on demand and reporting to the BMS, as at Vida Dubai Mall.

Burner, pump and temperature control with safety interlocks for hot water and steam boilers serving several floors.

Protection and distribution panels that connect solar PV inverters to the building supply and make the most of solar output.

Reduced-current starting and protection for large fans and motors, for smooth starts, safer operation and longer motor life.

Motor control, start sequencing and weighing for crushers, conveyors and mixers, with HMI recipe screens for material weights.

Control of pumps, nutrient dosing, lighting, temperature and defrost for hydroponic fodder and crop units.

Ultrasonic energy and flow meters on chilled and hot water systems, with the data collected on HMI tables for billing and plant monitoring.

Control panels with radio remotes for overhead bridge cranes and winches in factory halls.
Total incubation control for hatcheries: temperature, humidity and turning, with an Arabic-language HMI.
Motor and process control for olive oil pressing lines.
Control panels and HMI screens for refining process lines.
Weighed material conveyors that feed the mixers at the right rate.
Filling and weighing control for bagging lines.
Compressor, evaporator fan and defrost control for cold stores.
Control panels for pallet stretch-wrapping machines.
Start, stop, speed and interlock control for belt conveyors.
Send us your single-line diagram or specification. Our engineers will reply with a technical offer and lead time.